Senshi - Project "Evangelion" Full Blown Street Drift

Continued . . .

I decided to fit a 10 row Oil Cooler to aid in cooling the oil down when drifting

I decided to put it in the front right bumper area, but as the window washer bottle was there, it had to go...

A quick check to see if it will fit.....

.... and then came the vents, not so tidy or pretty, but who's gonna look at that anyway...

Not such a mission to mount it either... and sits nicely....

A few Alu plating mounts did the trick...

Then I needed a few braided hoses and some hydrolic fittings...... Ye made my own hoses up, wanted the correct lengths and enough to do this

combo Oil Cooler and Oil Filter relocation...

Fitted the relocator and Greddy filter where the fuse box used to be located.... Easy reach was the point...

Connected up the hoses.....

And there it is....

And yes I also fitted the oil catch tank...

To be continued once again . . . .

Continued again....

Got a new oil catch tank.... Yey... But where to put it ?

So I figured I would put it where everyone puts thiers.... Then I figured this could be bad seeing as the pipes would run directly over if not

touch the turbo or downpipe.... Oil Hose / Heat . . . . Ua ua....

So I decided to swop it arround next to the intake side, much better.... No heat to burn pipes or oil...

Still to be further continued once more . . . .

Riekert wrote:

dude! how much was that thingey? want to get a off motor mount for my oilfilter too

Hey Dude, like $170 or somthing if I remember correctly..... I will need to check for you....

Total cost was like R4K or R5K though for everything on the relocation / oil cooler settup

Another continuation....

As you can see, the Coil Pack doesnt look too pretty at the front there, but this was always a temporary mission....

So I made a nice bracket for it and mounted it on the firewall...

And there you can see it, unfotunately only place it would fit and still look good...

Ye ye, to be continued once again.....

I was getting irritated with my break lines looking so sh!+ after removing the ABS pump....

So I went a picked up a few new pipes and fittings....

And tested out my new bender and flairing tool....

Then mounted my line locker and started with the new break lines...

Another continuation . . .

You will notice lots of bends where you may wonder what they are for and why... Well lets just say it's to ensure the greddy intake will fit

withought rubbing with the motor torque...

Well All done now and looking good... Taking up much less space while looking neat...

And yes, more continuation to follow

Do I need to say it? Yes, another continuation.....

After getting these pretty push on's, I realized they not gonna work due to the coil pack being mounted where it is and only having 10mm space

now to fit the hose...

So I went to get get a few even prettier fittings.....

Dont they look nice now? The threads tapped slightly skew, but works well by aiming the hose away from anything that will rub through....

You know what I am gonna say, To be continued . . .

Continued again . . .

Here we have some other pretty things..... First in line though are the red alu pullies...

Had to first clean and neaten up and prime the water pump mounting pully

Then sprayed it red to go with the Alu pullies

What a difference in looks.... Mounted picture to come....

To be continued once more.....

And the last continuation for tonight, seeing as I have managed 2 pages in one day...

As you can see from this old pic, what I initially thought looks good, actually does look crap, and was irritating me bigtime... So I ripped it all out again... Yes AGAIN.... And I know Derek gonna rip me about that again, lol

So I went and got a new Dicktator Harness

Wrapped some protection onto it....

And decided I was going to mount the dictator in the center console.....

That means I will need to make a hole right here in the firewall to keep the wires as short as possible, to maintain a good strong signal

So I made the hole and pulled the wiring through..

Then made a protective gromet to block from water and also protect the wires...

This will only be completed though once all hardware is installed to make sure I dont have to redo it all over again...

To be continued once I have more pics and get more work done.....

To think, Todays update started on Page 23 -----> http://200sx.za.net/phpBB3/viewtopic.php?f=6&t=6142&start=330

POWDER wrote:

Not such a mission to mount it either... and sits nicely....

.

Holy DIY Leadlight lol

ha ha, ye man, was to lazy to go get one, Thats actually compliments of Mr. Hotstuff.... If he didnt come up with the idea I would still be blinded today, lol, coz I'm still to lazy to go out and get one....

POWDER wrote:

ha ha ha, ye, Riekert does take that title hands down.... ha ha ha..... Riekert wins the "Most Lag" award.... 🙂

Haha hey! 😳

Its true though... 😳 :domo:

Fo sho man..... But u still have one hellava nice project there.... U gots the SR in and running yet ?

Thanx man! and no not yet, waiting for some pricing to rebuild the bottom end. get it balanced ect ect aswell.

Well done Micheal, looking good!! I would never rip you...now now you start getting your panties in a twist again and then the "drift crew" GANG BANG ME 🙂 🙂

Well done boet!! Well done!!

Ha ha ha, u take it to seriously slut..... Thanks man, need to organize a good get together again....

Ya that would be nice, but my SX is still hanging in the air...and will for a while...but still a lekker braai or summing is long over due..

We don't need no SX to have a braai bud !!!! Mine is also airborn currently anyway, and will be for a while 2 as u can make out

Cool...when,where,what,how....and why 🙂

After pay day, my place, meat, on a braai, because we can 🙂

OK cool, keep me updated please 🙂